OPC UA Driver Timestamp
Hi, Is it possible to configure the OPC UA driver so that it ignores the timestamps provided by the OPC UA server variables and instead uses Zenon’s internal timestamp? Currently, for OnChange archives, the timestamp is taken directly from the OPC UA
The Screen is not full
One thing I can do is remotely access the service engine via the remote desktop client (Microsoft), but there is a problem: the service engine screen is cut off as shown in the image, and this unfortunately makes things difficult for me, because I also
Long connection time when working with B&R redundant PLC and OPC UA
hello, i am working on a big project where we work on B&R redundant PLC, the SCADA system is Zenon 14, the connection between the PLC’s and the SCADA is OPC UA with highest level of encryption with certificates. the connection is made with one IP address
Factory inventory
Greetings I have a customer who is interseted in using IMM in their Zenon application. But they would also like to keep a inventory of spare parts. Are there anybody that have implemented Inventory in Zenon? By a third party software or directly thru
Zenrt32.exe - Assert Failure
Dear Copa-Data support team, Our application froze and showed this error message. From this point on the panel where the application is running is completely responseless, and had to be removed from power to be restarted. For more context, the screen
Scalability and Device Management for Large Profinet Networks in Zenon
We are planning a project where Zenon SCADA will communicate with over 250 energy meters via the Profinet protocol. Each device will send approximately 15 measurement values. Can Zenon handle communication with at least 250 Profinet devices reliably?
Disabling Alarms for Specific Equipment Groups in Equipment Modeling
Hi, I need to disable certain machines or parts of machines due to maintenance or because they are not yet fully implemented. We are using Equipment Modeling to define machines and their components. However, I’m trying to figure out how to disable alarms
Sollwerte intern abspeichern und wieder rücklesen
Hallo zusammen, folgende Situation: Aufgrund eines SPS-Ausfalls sind alle vom Betreiber im Laufe der Zeit eingestellten Sollwerte "verloren gegangen". Daher soll ich die Sollwerte intern abspeichern und nach einem Ausfall mit den internen Werten die Sollwerte
Linux Operating System
Does Zenon Scada run on Linux operating system? If Zenon Scada runs on Linux operating system, what are the requirements?
SystemModelGroup(Equipment Group) Decoding to Human Readable Format
Hi, How can the SystemModelGroup (Equipment Group) from the project SQL database be decoded into a human-readable format? Example in Zenon Editor: Variable: Tank[56].Lock Equipment Group: Incom.Lokacija.Obrat 1.Maturacija.Bazeni.Bazen 56 Example in the
Change Frame Size
I am trying to dynamically change the frame size in my SCADA project. One of the solutions I attempted is using an add-in with the following code: namespace AddInProjectService1 { /// <summary> /// Description of Project Service Extension. /// </summary>
3 Frames 1 Screen
I have three different frame sizes with the same zoomable content screen: Frame 1: 1920 x 1080 Frame 2: 3840 x 1080 Frame 3: 7680 x 1080 Is this possible? What is the best way to achieve this?
Creating file failed
Hi everyone, i just converted a project from the version 5.50 to the version 10. After that, i start gnereting the RT files but i'm encountering many errors like: Creating file "C:\Users\Utente\Desktop\RFE078\SRFE0078\RT\FILES\zenon\custom\graphics\Button_Alarm_Bell_Mask.gif"
Elements Gestures c#
Hi Support ! I use Element gestures (till now i only used "tab") So if i implement element gestures like this: example for test: IProject AP = null; public void Start(IProject context, IBehavior behavior) { context.ScreenCollection.ElementGesture += ScreenCollection_ElementGesture;
Zenon Logic Does Not Update Internal Variable Timestamp on Internal Value Change
I've encountered a bug in Zenon Logic where the timestamp of an internal variable (Driver for internal variables) is not updated when the variable's value is changed from within Zenon Logic. This leads to several issues: Alarm message list displays incorrect
How to Retrieve "Description" Field from CEL in Report Builder
I am using Microsoft Report Builder connected to Zenon to generate reports using data from the CEL (Chronological Event List). However, I noticed that in Microsoft Report Builder, the default Data Set named "CEL" does not include a Query or Fields for
Service Engine shuts down after closing filtering page by clicking OK
Hi, On v14, whenever I try to modify column headers on filter window, Service Engine shuts down a few seconds after I hit OK button on filter window. As I have no opportunity to save the desired filtering settings, I come accross with the default alarm
Production and Facility Scheduler - import
Could you please give me a hint on how to import data for Production and Facility Scheduler, prepared in advance e.g. in the form of an Excel spreadsheet?
Zenon V14 installation failed
Hi, I was trying to install the Zenon version 14 but facing an error. Error file attached for reference. Please advise the resolution. Operating system is Windows 10 Enterprise having build 19045 and Admin rights are enabled on the PC. Thanks.
Process Gateway Issue
Hi.. I Have an Issue, during Service Engine Runtime, i have 2 process gateway to publish for our customer. Now our process gateway very often closed automatically every 1 day passed, every that happen i need to close runtime and running the service engine
[FEATURE] Extended Trend - Option to Position Gantt Charts Above Trend Diagram Automatically
Hi, To significantly reduce the time required for configuring Gantt charts displayed above a trend diagram, I’d like to propose adding an option to place Gantt charts directly above the diagram. For reference, I’ve attached a screenshot illustrating the
C#: Calling page and used filter
Hi there, I try to read out the page name and the used time filter of the page which was triggering the C# code. Target is to read out "...TimeFilter[0].ARVTime1" of different pages with the same program. Zenon V14 Thanks for any help. Regards
IEEE C37.118 data archiving every 20 ms
Hello, We would like to archive PMU datas. We are getting PMU datas over IEEE C37.118 Zenon logic drive to the Zenon Energy Edition 14. And Resolution of PMU datas are 50 samples per seconds. It can be 200 samples per seconds in some special application
NX1P2 slow communication
Hello, I have a problem with relatively slow communication between PLC NX1P2 and Zenon. I use 3400 variables in the project. When I open a new window I have to wait 1-2s before all variables are loaded. I have set the refresh priority of variables between
CEL logging
Hi all, I have question about logging in CEL. We use INT variable for commands (MOTOR_CMD), with the following values 0 - IDLE 1 - START 2 - PAUSE 3 - STOP CEL logging activated via dynamic element and checked Old and New value. So, when operator press
61850 communication issue with bufferd RCB RCB
Hi I have configured a buffered Report Control Block (RCB) in a Siemens relay and imported the ICD file into zenon. However, zenon is not enabling the buffered RCB. What could be the reasons preventing zenon from enabling the report? I have already configured
Automatic Line Coloring in Zenon Energy Edition 8.20
I'm working on a substation SCADA project using Zenon Energy Edition (v8.2) and need guidance on setting up Automatic Line Coloring in Zenon Energy Edition for the single line diagram. My goal is to change the colour of lines, busbars, and breakers based
Driver errors
Hello, Please refer to the attached photo, whenever we run the runtime we are always experiencing 100% CPU usage which causes the server to be unresponsive and takes a long time to load. Many drivers are showing this error. Please advise us on how to
Compatibility with TIA v20
Hello, We are currently working on migrating to TIA v20. I would like to know if anyone has experience with this setup and can confirm whether Zenon 8.2 and v12 is compatible with TIA v20. Best regards.
Exporting Reports and Events to PDF Format in zenon
I would like to know if it is possible to export Reports and Events to PDF Format in Zenon. If this functionality is available, could someone please guide me on how to do it?
New User- Communication of 'AccessDNP3_SG.dll' cannot be initialized! Please check configuration.
Hello Zenon Community, My name is Yusuf Khan. I've been using it for past 1 year but am new to Process Gateway configuration. I'm currently working on a Substation project where I need to out the data on DNP3 to SICAM PAS(Siemens gateway software). I'm
Zenon Version Update
Is that possible and easy if i update zenon version from Version 11 to Version 14. In Live System ? What things that i need consider to update the version, and is the License still can use in the new version or not ? Thanks as always
Trending Page Configuration
Hello. I need help with a recurring issue. On the trending page, each variable requires the value range to be set using the Automatic Scale; otherwise, the y-axis and curve display become messy. However, this becomes quite troublesome when I want to display
Assigning system variable DWORD1 to local internal variable
I’m not sure if I’m in the right forum: Why can't I assign a copy of the system variable DWORD1 to a local internal DWORD variable? Unfortunately, the local internal variable remains 0. Best regards, Henry
Export data
Hello, Zenon Community, I have an issue with exporting data. Firstly, the buttons on the "Alarm message list" and "Extended trend" screens don't export data. Besides, I added an export function as well. However, the situation is the same. Secondly, the
"Move frame via mouse" function over Dynamic text
Hi Everyone I am using the "Move frame via mouse" feature to be able to move the screen position when starting the service engine. However, currently, when I place the mouse cursor over a "Dynamic text" element, I can't move the screen, while it works
Event and Report export in PDF
I'm currently using Zenon Energy Edition 8.20 and looking for guidance on how to export Events and Reports in PDF format. Specifically, I'm interested in knowing whether automated or scheduled hourly exports of both event logs and reports are possible
How to acknowledge alarm if it has been cleared before acknowledge
Hi all, I'm having an issue with the acknowledge alarm. As you can see in the picture, there was an alarm temperature, which I did not acknowledge. currently the value is lower than the limit value now , but it remains alarm and cannot be acknowledged.
[FEATURE] Process Gateway OPC UA Server - Support for Publishing Raw Values
[FEATURE] Process Gateway OPC UA Server - Support for Publishing Raw Values Currently, the OPC UA Server does not support publishing raw values directly from the PLC. It only publishes adjusted (scaled) values. This limitation severely limits OPC UA Server
Zenon Redundancy
Greetings, Long time since my last post. I need all sections within Zenon (V11) documentation about redundancy. I have 2 servers with Logic drivers working on both. Server 1 (primary) > at normal conditions, the Logic drivers should be active and running.
Next Page