Button flashing
Hi, how to make a button that will start to flash when a new alarm appears? There are more then 100 alarms that trigger button flashing. What is easiest way to do it? Regards. This is a migrated post! Originally posted on 19.04.2013 by user tihomir. Please
acknowledgment alarms
acknowledgment alarms Dear Support, I have a little problem with the AML screen. IÂ've been working with it without any problem, but I donÂ't know how, now, the alarms can't be acknowledged or deleted. the buttons are desactivated. the alarms came from
S7 TCP-IP simulation
Hi, In my zenon project I have S7 TCP-IP driver installed and over 1000 variables imported from S7 project. What is the best way to simulate the behavior of variables? I want to manually simulate both states ( 0 and 1) for every single variable, one by
Context menu Command in touch panels
Hi I need to know how i can open the contexmenu of the dynamic elements with the left mause button because I'm setting up a touch panel and activate commands need the same button. thanks in advance This is a migrated post! Originally posted on 15.04.2013
DLL Error
Hi Support, After installation of Zenon Energy Edition 6.51 SP0, I am receiving the below error if I try to open anything related to Zenon (Editor, Runtime, Licensing etc) "The ordinal XXXXX could not be located in dynamic link library mfc90" This is
Read Date & Time from Time Attribute on IEC61850
Hello, I would like to read date and time from variable and display it in numeric field.I am using IEC61850 driver. I have tried to do this by mapping the time attribute of that specific variable. When I import the variable in zenOn the data type it is
Writing Cell values from Reports to Internal Variables
Dear Support, I am trying to write some cell values from a Report to Internal Variables, but it seems like not happening. I am using the below function: = variablerw('variablename', 'value', 'read') I have tried by writing 'write' instead of 'read', but
Issue with Loading the last used Workspace and Project
Dear Support, I am using Zenon Energy Edition, 6.51 SP0. The problem that I am facing is stated below: I create a Workspace and a Project in Zenon Editor and start doing the Engineering. Before exiting the Editor, I create all Runtime files for the Project.
Problem with interlocking
Hi, i want to solve a problem that we have with the interlocking, and perhaps you have an idea. We have several screens that are identical and each screen communicates (its variables) with a different RTU. For each screen we only change the variables
Replacing links for Variables, Functions and Screens
Hello, I have made a project in which the name of variables, functions and screens starts with SS440-XXXXX. This project is for Substation 440. We are using IEC61850 driver. Now I have to make another project for Substation 450. Both of these substations
Analyzing IEC850 data log in Diagnosis Viewer
Hello, I would like to know how can we check whether we are getting data by Polling or Reporting from Diag Viewer? Which settings for Client/Server are required plus which columns needs to be selected to view polling or reporting data on IEC850. Currently
Importing Files from IEDs on FTP and TELNET
Hello, We are using SEL IEDs and want to retrieve the oscillography and event files. SEL IEDs support TELNET and FTP to retrieve this info. How can we achieve this in zenOn? Could you please help? Thanks This is a migrated post! Originally posted on 04.12.2012
Status of Action Variables in Runtime
Hello, When will the Progress bit of Action variable is high? We want to monitor the Progress status bit of Action variable during runtime. Is it possible as we can monitor the Progress bit of Response Variable? Thanks This is a migrated post! Originally
IEC60870 Driver Communication Status
Hi, we have tried to discover an IEC60870 driver variable that tells us that the communication with the RTU is not OK .In the help we have read that some drivers don't give this information and we haven't found such a variable. ¿Is there any variable
Configuring interlockings
Hi, we are testing the commands with the IEC 60870-101 Driver. The ON/OFF commands, configured with select and execute work perfectly but the interlockings don't work. This is being tested with the standard template provided by Zenon. We have configured
DNP commands
Hi, I have to use DNP pulse commands , how we can configure the same in Zenon 6.51 SP0. DNP3 slave needs pulse commands. TIA This is a migrated post! Originally posted on 26.09.2012 by user ansab.tp. Please be aware that information can be outdated.
IEC 103 Distrubance Record
Hello, Kindly advise how to extract IEC 103 Fault records from Relay. In the IEC 103 driver properties there is a location for saving fault record but when i trigger fault nothing is saved. Regards This is a migrated post! Originally posted on 26.08.2012
does zenon support FDT?
FDT=Field Device Tool;) This is a migrated post! Originally posted on 11.07.2012 by user zhangbb_dimension. Please be aware that information can be outdated.
IEC101/104 server
I designed Zenon as HMI control center, and others PLC controler connected via IEC61850. Now my custumer require HMI software has to provide gateway controller to connect to Region Dispatching Center( as Scada system). The communication protocol need
Play back data historical
Hi Can I do with zenon energy version to play back historical data ? I want to display historical information from system via chart, trends, data tables and graphical also to make a video playback the fault happened ( CB status, trip indication ...) Best
SICAM230 runtime crashed
I have a rumtime system with verison of 6.51SP 0 Build 0. Now I added a self-increased variable by driver MATHDR32, the formula of the variable is X01+X02/1800, X01 is the variable , X02 is a certain process value comes from the process device. Unfortunately,
Use two instances of one driver
Hello Can I use two instances of the IEC61850 driver simultaneously? One for Relay protection 110kV and one for Relay protections 20kV. Is there going to be a problem with report control blocks? Anybody with such experience? This is a migrated post! Originally
Assigned RCB was not found
Hello I have a MiCOM P442 protection that is connected to a Zenon 6.51 SP0 Build 11 system. Protocol is IEC61850. I have connected the device, online browsing is working, polling is working. I am trying to enable a BRCB or URBC on the device with no success.
Reaction Matrix
Hello! Is there way to show measure values in recation matrix? For example, a measured value will only be send when a fault happen and this value i have to show in event list? Thanks and regards, Archie This is a migrated post! Originally posted on 22.05.2012
Command REG-DA OLTC with IEC61850
Hello I have an a.eberle REG-DA oltc controller, connected via 61850 to a zenon 6.51 SP0 Build 5. Connection and communication is working. Can anybody advice how to realize the command for Lower/Higher the step position? According the IEC standard "Binary
Micom Px4x URCB/BRCB problem
I am trying to integrate a couple of Schneider/Areva Micom relays series 4, protocol 61850 to Zenon 6.51 SP0 build 5 system. Connection to the devices is working. Polling mode is ok. When I make a URCB available and start the Runtime the driver connects
How to send a spontanous command to RTU?
Hi I have a Zenon 6.51SP0 communicating with a SICAM AK1703ACP RTU Communication is made using the IEC870 - 104 protocol System reads correctly spontaneous data generated from RTU. What I want to do is generate a "spontaneous signal" to set some digital
help in Sicam 230
Hello, 1 I am working on the Sicam 230 editor and trying to read the system time into AK 1703 PLC with the help of 'write time to variable ' function but to read this value in the PLC i have make that images in the TOOLBOX II's OPM image editor for sicam
Problem with IEC 104.
Hello, How do I create a two-step command select/execute on IEC104? I needs to communicate with ABB station. Best regards, Miroslav This is a migrated post! Originally posted on 03.05.2012 by user brada. Please be aware that information can be outda
SICAM 230 with ABB RTU560CMG
I am trying to replace MicroSCADA SYS 500 with SICAM 230 6.51 to communicate with ABB RTU 560CMG. I can communicate with the RTU over ethernet but i can not send any commands to RTU. I have the IEC 104 parameters taken from RTUtil560 as excel export.
Mean of Archived Values
Hi Support, Using Zenon 6.51 is there a way to calculate the Mean of Archived Values and display it in the Reports (using report generator module)? Please note that I am not interested in displaying all the values (for which I want to take the Mean) in
Error in topology
Hi; I have a problem in topology called "Zweipol zu oft angeschlossen".What is the meaning of this error and how can i solve it. This is a migrated post! Originally posted on 04.03.2012 by user sahbazh. Please be aware that information can be outdat
Command function in energy edition
Hi, I'm having problem to link this command to context menu. When ever I ran the runtime and click on the assigned combined element, the context menu does not appear. Please show me the correct way to create command cotext menu and link it to combined
probleme laoding a new driver
Hello, When loading a new driver, I got an error message "the module can not be loaded! The Last erroer: 0x00000000". What should I do? I am grateful for your help. Thank you in advance Sincerely, This is a migrated post! Originally posted on 14.02.2012
ALC undefinded line question
Hello! We have some question about line colouring when two lines are shorted with two switches one in closed and another in undefined state. In that case next inactive line after some other closed switch is coloured by undefined color (black) (see files
Please help me with settings IEC870
I want to test IEC870-104 connections with Siemens SICAM PAS. SICAM PAS is slave, ZENON-master. PAS settings contains ASDU adress and IP ZENON contains : 1. Net adress 2. IEC COA Where I Should paste ASDU adress from PAS? In Net Adress or COA? This is
IEC101-104 Error
HI all, Please check attached log file. I am communicating through IEC101-104 driver. And communication is proper but I am not getting values. Using Diagviewer I saw that there is an error. This is a migrated post! Originally posted on 05.01.2012 by user
energy calculation in zenon 6.51
Dear Mark, Can we calculate energy value (like Whr,Varh) in zenon 6.51 using mathematical variable if only parameters available from relay are voltages, current,power, power factor and frequency? This is a migrated post! Originally posted on 26.12.2011
Calculating energy
How will I calculate energy if the only data available to me from the relays is volts, power and current. Moreover I could not calculate the energy as there is no formula available in the mathematical variale for integration (integral). Your support and
IEC 61850 disturbance file extraction
Hi How we can extract the DR files from IEC 61850 relay. Can you advice please... This is a migrated post! Originally posted on 25.11.2011 by user ansab.tp. Please be aware that information can be outdated.
Next Page