Firewall prevented packet sent from PROFINET device to be received by PROFINET controller in zenon Logic
When straton (zenon logic) is started the first time, the firewall configuration dialog pops-up. By default you allow connections for private Network but not for public networks. When using a second network card this connection is classified by default
Logic processor compiling error
Hi, While compiling the project in the logic editor for GPS_SSS_RPR, I am getting errors on the digital program. Have you seen this error message earlier? Variables were set to externally visible in the client side. BR, Deepak This is a migrated post!
Error in compiling ('buid start up project') in logic processor
Hi, While compiling the project in the logic editor, I am getting errors on the of the program- see snapshot below.Have you seen this error message earlier? If so, how do I fix it? BR, Deepak This is a migrated post! Originally posted on 04.06.2020 by
Connection between zenon variables and zenon logic
Hello, I have a problem with connection between zenon variables and zenon logic. I created boolean intern variables in zenon (8SP0 64bit), then I checked 'Externally visible' in all of them. In zenon logic project I inserted connection 'Logic to SCADA
Configure 1756-ENBT with Zenon Logic
Hi fellow Copa Data, I would like to ask, how is possible for me to establish communication between Allen Bradley 1756-ENBT Ethernet/IP module with Zenon Logic? I have been trying using the tutorial given in Zenon Logic, but I never get the EIP module
VACO is not counting (Runtime event: "Embedded Software missing: VACO")
Hello, I am starting a fresh project in Zenon Logic. I connected two counters to a VACO function block. However, the VACO counter is not counting and the Runtime event viewer is showing "Embedded Software missing: VACO" What could be the problem? thanks
straton program organization lost
hi i open my straton IDE today click on my project list all my program are now in the same folder Programs before i had a folder organization for each where is this folder organisation stored ? folder organisation before: now: This is a migrated post!
Logic Error - PLC utilization peaked at 156%
Hi all, I constantly see an error message on diagviewer for straton. Like "Timing configuration error. PLC utilization exceeds 80 Configured cycle time = 10260 us, maximum execution time = 16038 us, maximum PLC utilisation = 100". It is working some how
SCADA Runtime Connectivity
Hello. I have a problem with my Zeon Logic, my external visible variables are visible in the Zenon Logic, but the values are not visible. This means that, if I change the value of the tag in Zenon SCADA, there is no change in the Zenon Logic. The same
Zenon Logic MQTT
Hi, I would like to configure MQTT in Zenon Logic (Ver 8.10). But I can't find MQTT features in Field bus configuration list. I can only see functions like MQTTConnect in the program. Do you have any documentation on MQTT ? Thank you. This is a migrated
DiagViewer statement error trace
Hello guys, In the DiagViewer I have an error in my logic referring to to a certain state as shown in the following example : Project 'Gilon_logic': Error connected T5 runtime has invlaid state. Project name 'Gilon_logic', state '9402'. My question is
Ethernet/IP Server and Ethernet/IP/I/O Scanner
Hello, We have two straton running on two different PC's one is act as Ethernet/IP Server and another is Ethernet/IP/I/O Scanner. As per given in help we have configured the required settings(e.g. instance, attribute)in both scanner and server but still
Hexadecimal to ASCII Coversion
Hello, Can we convert Hexadecimal input to ASCII output using standard block in Straton? e.g I need to convert '31 32 33 34' to ASCII as "1234" and likewise others. Thanks & Regards, Rahul. This is a migrated post! Originally posted on 06.11.2019 by user
Converting of IEC61850 integer values into Bit wise
Dear We have almost 900 IED in a project each having four function blocks to combine digital alarms and send it as integer value via 61850 to Zenon. 1-I need to know if Zenon logic has a standard Function blocks to reconvert the integer values back to
Control IEC61850 function block
Hi sir I want to control SPC variable within zenon logic. I will use IEC61850_WRITE function. it explain that PATH STRING Path to data point (without "ServerName!") IF I set path = Bay431!BAY431System/PloGGIO1/SPCSO1/Oper.ctlVal[CO], your program said
Zenon Logic --> S7 300 Connection
Hi everyone! I have just a short question to Zenon logic. So, we make a test, we would like to communicate with S7 300 PLC, but direct with Zenon Logic (we have a soft PLC and our aim is a PN connection). By SCADA site operate the communication well,
Cycle read file
Hi All, I use this code to read data from a file: The first time I run, It's correct, like this: I saw that the ID1 increase step by step, and then when ID1=32 then return to 0, it's not correct, like this: Could you please help me to solve this. This
STRING to TIME
Hi All, I read a string from *.csv file : 15-05-2019 09:00 How can I change this STRING to the right time? I used ANY_TO_TIME, I just only get time==15ms. Thanks. This is a migrated post! Originally posted on 04.06.2019 by user kieuminh. Please be aware
Execute Function Block in Straton
Hello, What is the role of execute block in Straton? Can we provide command (e.g. T45 COA=1, IOA-2) without using command processing window if we use this block in straton? Regards, Rahul I. This is a migrated post! Originally posted on 24.05.2019 by
Straton - Fieldbus configuration API
Hello. How change parameters in fieldbus configuration in C/C++ (for example Interface or Device address)? Do you have API for this? This is a migrated post! Originally posted on 07.05.2019 by user mhanusek. Please be aware that information can be o
Difference Between testBit/setBit and variable.bitNumber
Hi , Suppose that i have a word variable like xWord (which is imported from OPC server) and i want to read or set some of its bits.(in following example, xbit is an internal zenon variable which is visible in Scada Logic) What's the difference between
XML utf-8
In a project i read some information from a xml file with zenon logic. I haven't got problem. I need to translate my project in chiness, and i have some problem with convertion. this my xml file 0-与PLC连接不工作@GENERALQiyu¡n : PLC不工作\n网络故障\nJie : 检查PCL供电\n检查网络布线\n检查HMI网络配置C:\GCX\ROBOACCESS\RT\FILES\zenon\custom\additional\GCX\DOC\ALARMS\ZH\0.html1
elmo drive canOpen mapping reseted
Hi, In my application i am using 3 elmo gold drive, at a time it seems that i loose the canopen mapping of one of my drive: my drive Id are 2,5,7 6 is a canopen inclinometer 185 8 37 16 81 30 03 00 1B 00 182 8 37 16 3B FD FF FF 17 00 187 8 37 16 CA C6
Get fault current in zenon
Dear Sir I want to get fault current in Micom Relay on 61850 protocol. But the fault current is triggered in short time and I cannot capture peak current value in Zenon. The value of current is alway changed Could I capture its on Zenon logic Thank you
Straton IEC60870-5-104 Receiver Set poit command
Good morning, I should configure a slave 104 to receive set point command, but I have a a question to ask you. I receive the normalized value correctly, but I would like to know if there is a bit that gives me the information of "setpoint commad received"
Straton runtime for raspberry pi with mysql, where?
Hello, where can I get a Straton Runtime with mysql support? For a Raspberry Pi or a linux system. The versions to download have only sqlLite support. Thank you This is a migrated post! Originally posted on 31.01.2019 by user sesins. Please be aware that
Straton PT input as ms
What is the procedure to input timer PT values as something other than seconds? This is a migrated post! Originally posted on 01.11.2018 by user Geezerglide. Please be aware that information can be outdated.
control 2 variables in graphic/pushbuton
hi i would like to know if it is posible in a graphic/pushbuton to control to variable at the same time for example a BOOL value and an analog variablestate of the button will be only the BOOL variable of course This is a migrated post! Originally posted
Embed symbol checkbox.
Hi, I want to modify variables by zenon Logic, but cannot manage to check "Syb." checkbox in Straton. I'm getting message "The variable is currently locked". Any idea what should i do? This is a migrated post! Originally posted on 09.10.2018 by user www121212.
Integrate/Connect/Link HMI graphic with PLC instructions
Hi COPA DATA I want to ask regarding on how I can link/connect/integrate my PLC instructions with HMI that I created in Zenon. Currently, I am using WAGO 750-8202, DI card (part number: 750-1405) and DO card (part number: 750-1504). I read the manual
Recipe not loaded properly
Hello, I have a problem with straton: I want to save+load some values using the integrated recipe manager. However it appears that some values are not saved/loaded properly ! The same problem appears by saving or reloading values to/from the recipe. Here
zenOn Logic - speed-up download?
Hi guys, I would like to know if there is a way to speed-up the program code download from zenOn Logic to the target. Right now on my development PC with an application code APPLI.XTI / STRATONRT.COD from about 1.2MB, it takes about 40s to download to
F_DELETE false
How to figurout why file wont delete? Image attached. This is a migrated post! Originally posted on 06.09.2018 by user klasik. Please be aware that information can be outdated.
Error with function structure member.
Hello, Iam programming with the IDE Straton. Iam trying to use 2 structure parameter, one 'IN' and one 'OUT'. The types of the structures are the same ACCE_QUALITY. ACCE_QUALITY : - validity : BYTE - detailQual : ACCE_DETAIL_Q - source : BYTE - test :
Problem with Version Control
Hi, Is there anyone using Straton with SVN client? I got problem with it and find no instruction in Straton Help. After installation of Zenon 7.60 on my PC (Win7), I created a Staton project and enabled the Version Control in Project Setting. There I
Problem with Autotstart project in Straton Runtime Manager
Hi, The Autostart project (Straton Runtime Manager) does not work on some of my computers. Does anyone know if there are any registry setting in Windown 10 that prevent Staton Autostart? This is a migrated post! Originally posted on 11.10.2017 by user
Anyone using Straton with Hilcher gateway on Profinet IO?
Hi, I am trying to using Hilcher gateway NT50-DP-PN (profibus DP to Profinet IO Device) with Straton PLC. I set up and Profinet IO Controller in Straton and try to connect to Profinet IO Device (Hilcher gateway) but did not suceed. The Straton alway return
Straton runtime not starting.
Straton is showing an error 'embedded software missing function: ICOPY'. Please help me with this, as it is causing a big issue now This is a migrated post! Originally posted on 14.10.2017 by user joelprasad. Please be aware that information can be
Writing status bits on Zenon Logic Global Variables
What kind of status bits are settable from Zenon Logic on Global variables? I've found that none of M1..M8, ALT_VAL are settable (or almost are not visibile from Zenon Runtime) I'm using STRATONNG driver. This is a migrated post! Originally posted on
Automatically build using the STRATON development environment
Hi, I have a STRATON project (W5L and K5P files). I would like to automatically build the project so that I can check for errors. Is this possible using the automation interface or via the command line? I have the STRATON Development Environment which
Next Page