Various Problems about Sicam230 6.22 SP1 Editor
Here are some problems I've encountered while using Sicam230 Editor in different times of working. Some of them are about user-friendliness and some of them are bugs. But all of them make the program annoying and hard to use most of the times. * while
question IEC850
Hello Mark! I am experiencing the same problem with jusufs.But I cant understand your discussion since your using your local language ( austrian I think?) . What is the solution for this one? I am using zenon 6.22 sp1 and windows server 2008. Attached
Iec61850 Error
Hello! Kindly help me with this one, I am having error whenever I download variables from a device using iec61850 protocol. I am using ZENON 6.22 SP1 and the operating system is WINDOWS 2008 STANDARD. here is the error message " an unhandled exception
Fragen IEC850
Hallo. Ich bin fur grosseres IEC850 Scada Projekt im SAS Bereich zustandig. Habe leider Crash Problem zu losen. Weiter mochte ich sie bitten mir Paar Fragen beantworten. 1. Was kann Crash vom IEC850 Treiber verursachen - siehe Beilage ? Project nutzt
IEC driver TIME OUTS
helllo it is some way to change TIME OUTS (see picture "IEC.jpg") for IEC 870 driver? Duncan This is a migrated post! Originally posted on 16.12.2009 by user duncan. Please be aware that information can be outdated.
IEC 870-103 driver
Hi all I tried to receive some 103 point from AREVA relay using driver IEC870_10332 via serial port but all variables display status i-bit. I also check function type and information number that correct in AREVA manual. Has anybody tried with this and
watchdog for IEC61850 device
Hi Mark!:):) How can I create a watchdog for an IEC61850 device? I need to show it in the screen if the device is healthy or faulty? Will I create a system variable for this one? Thanks! This is a migrated post! Originally posted on 03.12.2009 by user
IEC 104 primary and redundant IP addreses
Hello, Is there any way to change switch over time between primary and redundant IP addreses? Now, when primary IP goes down, conection to redundant IP is established after about 1 minute. How to decrease this time? regards, Justas This is a migrated
Re: Sbo
hi but what's reason in DNP3 when I select SBO in project variable and I executed the command processing,expired SBO message display for me in command picture and command sent to device in the direc way. This is a migrated post! Originally posted on 28.10.2009
Sbo
I’m working in a project using IEC61850 protocol. I did activate the SBO in one the control variables. But during RT I made command directly using the said variable without prompting me with some selection. As per my understanding of SBO, there will
Bug
to configure Double command "ON" the "Command setting status" must be "2" but in the editor you can choose only "0" or "1"... the only way to do it is by hand using XML file:( This is a migrated post! Originally posted on 23.10.2009 by user westbaaam.
IEC 101-104 T09 measured value
Hello we have some problems with measuered value, we send some value to SCADA but SCADA display incorect value. Where is problem? Other scada (not Zenon works OK). Othere type of signals T02, ....... works OK. This is a migrated post! Originally posted
ALC interlocking
Hello! I would like to use ALC interlocking "Disconnector under load", but it seems it does not working OK for my purpose. E.g. I have a disconnector which is supplyed only from one side. On the other side it is undefined (not supplyed) and I get the
Accessing response variable using VBA
Hello! How could one get the name of the response variable from "Command" template using VBA? I made a script which is attached to start event of the "Command" template. If I use default control elements on the "Command" template, the response variable
Sending two commands at once
Hello! Is it possible to to send two commands (actions) at once using "Command" template and built in functionality of Zenon (e.g. I want to attach two different command variables to one action button). Best regards, Gregor This is a migrated post! Originally
Automatic line coloring (ALC) and DPI variables
Hello! I am trying to use automatic line coloring with procedural element "Switch" and DPI variable used for this switch, but I don't have any success. When using "Switch" with BOOL variable, everithing is OK, Info text from the manual of ALC says that
Picture Command Positioning
Is it possible to position the picture command pop-up relative to the cursor position on a multi monitor? Pop-up will always appear on the left hand side of the first screen when executed from second screen. Can VB be used to reposition the picture in
Problem with 61850 driver
I have a problem with 61850 driver in zenon. On my Laptop I have zenon 6.22 SP0. I connected it to a BCU and imported some command and response variables from 850 driver. Commands Data Type: BOOL Response Data Type: DINT When the command variable was
VERY URGENT. Zenon for dispatch SCADA station for the oil and gas
We have 3 SCADA system running with Zenon. The 3 SCADA system are interconnected through fiber optical network. (Hundred kilometers between each SCADA station) Each SCADA system is a master station connected to a slave IEC60870 or IEC61850 PLC unit. (This
COMTRADE files
Hello! Does Modbus serial and IEC103 master drivers support collecting disturbance data from protection devices and is it possible to view this data (comtrade files) in Zenon Energy edition SCADA? Best regards, Gregor This is a migrated post! Originally
action "COMMAND" at the dynamic element not visible
I do not have the option "COMMAND" at the set-value by option in the properties for the dynamic element. What do I need? A zenon energy edition license is required and second, the option "Windows CE project" in the project properties in the section "general"
Nt_bit
Hello, In Stati configuration screen, under Status, there is a checkbox for NT_BIT. What does it stand for? When will it be triggered? Thanks for the help. This is a migrated post! Originally posted on 10.04.2008 by user tauhien. Please be aware that
Zenon software & plcsim
Hi !! I have a Zenon software for touch screen and PLCSim from Siemens... i just wanna know if is posible to work togheter and what kind of drivers should i use...thank you This is a migrated post! Originally posted on 13.03.2008 by user gh_ounie. Please
Importing variables for the IEC870 driver is hanging
When I import variables from the IEC870 driver in the editor, items are received, but then the count of items received stops and the import dialog remains forever at this number until I press cancel. Normally the import dialog (general interrogation)
project needs to be converted although the same version was used?
I used the zenOn standard edition version 6.21 SP1 to create a project and then switched to the energy edition version 6.21 SP1. When the project was loaded, it displays a message that it was edited in a previous version and if I want to convert it. Can
REMA and IEC870 timestamp question.
I have two questions. IÂ'm running Zenon Energy Edition with IEC870 Driver. Is it possible to "block" external timestamps for signals with "to big" time difference, compared to the zenon PC, If time is outside the limits, take local PC time instead? I
Normalized value with IEC60870-5-101/104
What is the normalized value with the IEC60870-5-101/104 driver? How do I configure the variable in zenOn? The normalized value, e.g. in the "set point command, normalized value" Type 48 - C_SE_NA_1, has a range of -1 .. + 0,99997 (1-2^-15 ). So the signal
IEC 61850 driver problem reading XCBR/Pos/stVal
Hello everyone! I have a problem with IEC 61850 driver. I've imported variables from an IED and enabled reports, everything works as it should with one exception. The driver reads different values of XCBR/Pos/stVal node than other software, for example
Select and Select before operate
What does the SELEC (Select) status have to do with SBO? (Select Before Operate) Nothing actually. The SELEC (Select) statusbit is set at the variable and broadcast in the network to all clients, as soon as the command window for this variable is opened
How to evaluate the locked state?
I can "lock" e.g. a switch by using Command in the energy edition. However how can I evaluate this status in other parts of my project? The response variable which is locked has the statusbit "ST_M1" set. This user-definable statusbit has this special
IOA addressing issue with IEC60870-5 104 driver in zenOn
In the PLC I have three octets for the IOA address. However in zenOn at the addressing information, only IOA1 is available. How do I address e.g. the Double Command (DCO, Type 46) correctly :confused: in zenOn, all the IOA fields are stored in one field,
Action buttons at the command interlocking
Why can I not select the single action buttons in my commands picture at the command interlockings? I can see them in the picture but they are not available at the dropdown box for the command operation. Please resolve all symbols in your commands picture.